Platinum Smelting in South Africa

 

R.T. Jones

 

Specialist Consultant, Pyrometallurgy Division, Mintek, Private Bag X3015, Randburg, 2125, South Africa

E-mail: rtjones@global.co.za

 

 

Introduction

South Africa has more than 80 per cent of the world’s platinum reserves, and is the world’s largest producer of platinum group metals (PGMs).  These vast resources occur together with the world’s largest reserves of chromium and vanadium ore in the unique Bushveld Complex geological formation.  South Africa’s PGM output is derived almost exclusively from the Bushveld Complex, with only about 0.1 per cent coming from the gold deposits of the Witwatersrand and Free State, and the Phalaborwa copper deposit.

 

Since the identification of economic deposits of platinum in South Africa in 1924 by Hans Merensky, a number of platinum mines have come and gone, and some have merely changed identity.1-3  South Africa currently has four integrated primary platinum producers, namely Amplats4,5 (Anglo American Platinum Corporation Ltd, formerly Rustenburg Platinum Holdings Ltd), Impala Platinum,6 Lonmin Platinum7 (which includes Western Platinum), and Northam Platinum.8  Their range of operations includes open-cast and underground mining, milling, flotation, drying, smelting, converting, refining, and marketing.  Amplats and Impala Platinum are the two largest producers of platinum in the world.  Since 1971, these operations have established South Africa as the world’s largest producer of PGMs.  The precious metals are the most valuable products in South African platinum ores, unlike the situation in many other countries where smaller quantities of platinum are produced as by-products or co-products of base-metal production, particularly of nickel.  Apart from South Africa’s platinum mines, only Stillwater Mine in Montana, USA, and Hartley Platinum in Zimbabwe are major primary producers of PGMs.  This factor is of great importance in the supply of PGMs, as South African producers are able to effect a marked change in the level of output of platinum within a relatively short time to conform to market requirements.9

 

Table 1 shows world PGM supply and demand by country, as well as PGM reserves.  It should be noted that the supply from Russia is believed to significantly exceed its actual production capacity, as a large part of its sales are from stockpiles.  As Russia does not supply official figures for PGM production, there remains some doubt about the accuracy of these numbers.  For example, other estimates show Russia producing only 2.98 million ounces per annum (Moz/a) of Pt+Pd.

 

Table 2 shows the production by individual companies of the economically most important PGMs, namely platinum, palladium, and rhodium.  Most production figures are from the 1998 annual reports of the companies,4-8 although the estimates for production at Noril’sk are based on news articles.  The most recent estimate of platinum production at Noril’sk10 is significantly lower than previous estimates (around 0.4 to 0.45 million ounces per annum).  Other 1997 figures have shown Russia producing 0.23 to 0.64 million ounces of platinum per annum.

 

 

Table 1:   Supply and demand figures11 for 1997 are given in millions of ounces (Moz) per annum.  PGM reserves12 are also shown in millions of ounces.  (1 million ounces = 31.1 metric tons)

 

Pt

Pd

Rh

Ru

Ir

Os

Total Pt,Pd,Rh

PGM reserves, M oz

SA supply

3.70

1.81

0.377

0.49*

0.80*

0.016*

5.9

2030

Russia supply

0.90

4.80

0.240

 

 

 

5.9

199

Canada supply

0.16

0.28

0.012

 

 

 

0.5

10

USA supply

0.08

0.27

 

 

 

 

0.4

23

Others supply

0.13

0.10

0.003

 

 

 

0.2

23

Total world supply

4.97

7.25

0.632

 

 

 

12.9

2280

Total world demand

5.20

7.46

0.460

0.357

0.127

0.005#

13.1

 

SA as % of world

74

25

60

 

 

 

46

89

*  The estimated figures for South African production of Ru, Ir, and Os are based on doubling 1984 production figures13, as has happened with platinum production over the period.

#  The figure for world demand of osmium is based on a 1993 estimate.14

 

 

Table 2:   PGM production figures for individual producers in 1998.

 

Pt, Moz/a

Pd, Moz/a

Rh, Moz/a

Pt+Pd+Rh

Primary producers of PGMs:

 

 

 

 

  Amplats

1.86

0.93

0.177

2.97

  Impala Platinum

 1.05*

0.56

0.112

1.72

  Lonmin Platinum

0.63

0.29

0.088

1.01

  Stillwater, USA

0.11

0.35

0.004**

0.46

  Northam Platinum

0.18

0.08

0.015

0.28

  Hartley Platinum, Zimbabwe

0.07

0.05

0.004

    0.13***

 

Producers of PGMs as by-products:

 

 

 

 

  Noril’sk, Russia

0.35

0.76

0.034**

1.14

  Inco, Canada

0.14

0.17

0.011

0.33

  Falconbridge, Canada

0.05

0.09

0.003

0.14

*     The figures for Impala exclude the additional approximately 30% production from toll treatment.

**  The figures given for rhodium production at Stillwater and Noril’sk are the author’s estimates.

***  Hartley started smelting in early 1997, and has not yet reached full capacity of 0.15 Moz/a Pt, 0.11 Moz/a Pd, 0.012 Moz/a Rh; i.e. Pt+Pd+Rh = 0.27 Moz/a.  Operations were suspended in 1999, but may yet resume in the future.  The production figures quoted here are the author’s estimates.

 

 

According to Johnson Matthey,11 the total world demand for platinum in 1997 was distributed as follows:

  Jewellery: 42%   Autocatalysts: 28%   Industrial: 25%   Investment: 5.6%

 

The total world demand for palladium was distributed as follows:

  Autocatalysts: 40%   Electrical: 34%   Dental: 18%   Other: 8.6%

 

 

Platinum-group metal ores

The currently exploitable South African reserves of platinum-group metals are concentrated in narrow but extensive strata known as the Merensky Reef, the Platreef, and the UG2 chromitite layer.  These three layers in the Bushveld Complex each have their own distinctive associated mineralogy, and have been well described mineralogically.15-17  The Platreef is mined only at Potgietersrus Platinum (Amplats), but Merensky and UG2 ores are mined by all the producers.  These ores are quite different from each other, and require different approaches to metallurgical processing.  For example, UG2 ore has a much lower content of nickel and copper sulphides, and contains much more chromite than Merensky ore.  The Platreef can be considered as metallurgically similar to Merensky ore, although somewhat enriched in palladium.

 

There are currently twelve active or very soon to be active platinum mines in the Bushveld Complex, eleven exploiting the Merensky Reef and UG2 Chromitite Layer, and one, Potgietersrus (an open-cast mine), mining the Platreef of the Northern Limb of the Bushveld Complex.  There is only one active mine on the Eastern Limb, namely the Atok Mine of Lebowa Platinum (belonging to Amplats).  The other mines are all on the Western Limb.  Amplats has the Rustenburg, Union, and Amandelbult Sections of Rustenburg Platinum, as well as the soon-to-be-opened Bafokeng-Rasimone Mine.  Impala Platinum is supplied by its own Impala Mine, as well as by Kroondal Mine (owned by Aquarius Platinum of Australia), among others.  Lonmin has Western Platinum, Eastern Platinum, and Karee Mine.  Northam Platinum has Zondereinde.

 

Ore from the Merensky Reef contains up to 3% base-metal sulphide minerals, distributed as follows: pyrrhotite (45%), pentlandite (32%), chalcopyrite (16%), and pyrite (2 to 4%).  The majority of the PGMs in the Merensky ore are associated with pentlandite, occurring either in pentlandite grains or at the pentlandite-gangue grain boundaries.  To a lesser extent, the PGMs are associated with other base-metal sulphides or occur in the form of minerals such as braggite, cooperite, laurite, or ferroplatinum.  The major gangue minerals are pyroxene, plagioclase feldspar, and biotite.

 

The principal constituents of UG2 ore are chromitite (60-90%), orthopyroxene, and plagioclase, together with minor amounts of talc, chlorite, and phlogopite, as well as smaller amounts of base-metal and other sulphides and platinum-group minerals.  The base-metal sulphides are predominantly pentlandite, chalcopyrite, pyrrhotite, pyrite, and to a lesser extent millerite.  The sulphide grains of UG2 ore are generally finer than those of the Merensky Reef.

 

Merensky ore contains much more sulphide than does the UG2 ore, and the minerals are found in a silicate substrate, while UG2 ore has a chromite matrix.  The Cr2O3 content of the UG2 ore presents major challenges in processing.  In Merensky ores, the ratio of nickel to copper is fairly constant at about 1.7, but the PGM to base metals ratio is not constant.9

 

The Merensky and UG2 reefs are situated in close proximity to each other.  The UG2 reef lies anywhere between 20 and 330 metres below the Merensky horizon, and varies in thickness between 0.15 to 2.5 metres.  Reserves of PGMs plus gold are estimated18 at 547 million ounces in the Merensky Reef, and more than 1000 million ounces in the UG2 reef.  Another estimate19 says the UG2 reef contains about 800 million ounces of PGMs.

 

The PGM content of the UG2 reef is comparable with, and sometimes higher than, that of the Merensky Reef.  The PGM content in the Merensky Reef ranges between about 4 and 10 g/t, whereas the UG2 reef contains between 4.4 and 10.6 g/t.  UG2 ore is by far the richest source of rhodium, which is currently the highest-priced PGM and an important constituent of the catalysts used in motor car exhaust systems.  The copper and nickel contents of UG2 ore are generally less than a tenth of those found in the Merensky Reef.  The Cr2O3 content of UG2 ore is about 30%, as opposed to about 0.1% for Merensky ore.  The low-grade chromite produced as a byproduct during the treatment of UG2 ore is also sold, and there is no reason why it could not be used for the production of ferrochromium.20  The high demand for palladium also makes the processing of UG2 concentrates very attractive.

 

Average grades and current values of the individual precious metals in Merensky, UG2, and Platreef ores are shown in Table 3.  Further detail regarding the distributions of the individual PGMs in various reefs and sectors of the Bushveld Complex is available elsewhere.16  The content and value of base metals in the three ores are shown in Table 4.

 

 

Table 3:   Average grades of the individual precious metals in Merensky, UG2, and Platreef ores,15 and their current potential value.  Market prices10 are as of the last week in February 1999.

 

$/oz

Merensky ore

UG2 ore

Platreef ore

 

Feb 1999

g/t

$/t of ore

mass %

g/t

$/t of ore

mass  %

g/t

$/t of ore

mass  %

Pt

379

3.25

39.54

59

2.46

29.98

41

1.26

15.35

42

Pd

350

1.38

15.47

25

2.04

22.96

34

1.38

15.53

46

Rh

860

0.17

4.56

3

0.54

14.93

9

0.09

2.49

3

Ru

37

0.44

0.52

8

0.72

0.86

12

0.12

0.14

4

Ir

395

0.06

0.70

1

0.11

1.45

1.9

0.02

0.30

0.8

Os

400

0.04

0.57

0.8

0.10

1.31

1.7

0.02

0.23

0.6

Au

287

0.18

1.62

3.2

0.02

0.22

0.4

0.10

0.94

3.4

Total PGM+Au

 

5.5

62.99

100

6.0

71.70

100

3.0

34.99

100

 

 

Table 4:   Typical content of base metals in Merensky, UG2, and Platreef ores,15 and their current potential value.  Market prices10 are as of the last week in February 1999.

 

$/lb

Merensky ore

UG2 ore

Platreef ore

 

Feb 1999

% in ore

$/t of ore

mass %

% in ore

$/t of ore

mass  %

% in ore

$/t of ore

mass  %

Ni

2.25

0.13

6.44

62

0.07

3.47

80

0.36

17.84

67

Cu

0.66

0.08

1.16

38

0.018

0.25

20

0.18

2.62

33

Co

18.00

 

 

 

 

 

 

 

 

 

Total BaseMetals

 

0.21

7.61

100

0.09

3.72

100

0.54

20.46

100

 

 

It is evident from the data above (as well as from actual revenues recorded by the producers) that Pt, Pd, and Rh make up a remarkably constant 95% of the value of all the precious metals, for all three ore types.  In the case of Merensky ore, these three dominant PGMs make up 80 to 85% of the value of all the metals produced (i.e. PGMs plus base metals).  For UG2 ore, the fraction is 90%.

 

The average grain size of the PGM minerals is about 45 mm in Merensky ore, and 15 mm in UG2.  In order to liberate the PGM minerals, UG2 concentrate is more finely milled (about 80% less than 75 mm) than Merensky concentrate (about 55% less than 75 mm).21  During concentration, the recovery of PGM+Au is around 80 to 87 per cent.21  Typical analyses of the Merensky and UG2 concentrates at Lonmin’s Western Platinum Mines have previously been published elsewhere.21-23

 

From a given quantity of ore, the mass of UG2 concentrate is lower (around 1.3% of the feed ore) than that of Merensky concentrate (around 2.5% of the feed ore).  Hence, the grades of UG2 concentrates are higher, and the amount of concentrate to be smelted is smaller.

 

The total cost of treatment of UG2 ore is claimed24-25 to be considerably lower than for Merensky ore, for the following reasons.

a)      Mining costs are lower, mainly because of the higher relative density of the UG2 reef.  The relative density of Merensky ore is 3.2 and that of UG2 ore is 4.3.15

b)      Crushing costs are lower because UG2 ore is more friable.  Milling costs are also lower.

c)      Flotation reagent costs are much lower, because Merensky ore requires the use of a talc depressant.

d)      Smelting costs are lower because much smaller quantities of concentrates need to be smelted (per quantity of platinum produced).

 

 

Beneficiation processes

Each processing step is designed to increase the grade (concentration) of the valuable components of the original ore, by reducing the bulk of the products.  The mined ore undergoes comminution, and a gravity concentrate is extracted.  The sulphides are concentrated by flotation.  The flotation concentrates undergo smelting and converting, to produce a PGM-containing nickel-copper matte.  The matte is treated hydrometallurgically to separate the base metals from the precious metals.  Finally, the PGM concentrate is refined to separate the individual precious metals into their pure forms.  As a rough guide,21 the PGM contents during the various stages are as follows.

 

            Ore                              0.0005%  (5 g/t)

            Flotation concentrate    0.0150%  (100 – 400 g/t)

            Converter matte            0.20%

            PGM concentrate         30 – 65%

            Refined metals  99.90% for Rh, Ru, Os

                                                99.95% for Pt, Pd, Au

 

During each separation stage of the process, there is an increase in the concentration of PGMs – about 30:1 in the concentrator, about 10:1 in the furnace, about 3:1 in the converter, and about 200:1 in the base-metals refinery.

 

For South African producers, the approximate distribution of the operating costs for each stage is as follows:26

  Mining: 72%   Concentrating: 10%   Smelting: 9%   Refining: 9%

 

PGM recovery is typically about 85% in the concentration stage, 95 to 98% in smelting, and 99% in refining.  By far the greatest loss of PGMs occurs during crushing, grinding, and flotation, and research into these operations could prove very rewarding, as could the development of new processes that remove some of the constraints on the various concentration stages.

 

 

Simple description of conventional matte-smelting process

A simple representation of the most common process is shown in Figure 1.

 

 

Figure 1:    Schematic representation of a typical platinum smelting process

 

 

Concentrate Drying

The concentrate is dried in a spray drier or flash drier.  This reduces the energy requirement for smelting, as well as decreasing the occurrence of ‘blowbacks’ or explosions in the furnace.  The dry concentrate is transferred pneumatically from the drier into the furnace.

 

Table 5 shows the analyses of the various concentrates.  Typical PGM grades are over 100 g/t for Merensky concentrates, and around 400 g/t for UG2 concentrates.  Some blending takes place.

 

 

Table 5:   Concentrate analyses

 

Al2O3%

CaO %

Co %

Cr2O3%

Cu %

FeO %

MgO%

Ni

%

S

%

SiO2 %

PGMg/t

Total%

Amplats

Waterval

3.2

4.7

0.08

0.80

2.1

20

15

3.6

9

34

143

92

Amplats

Union

3.8

2.5

0.04

2.59

1.1

15

20

2.2

5

38

142

90

Impala

4.1

2.9

0.06

1.1

1.3

18

18

2.1

5.6

42

138

95

Lonmin

Merensky

1.8

2.8

0.08

0.4

2.0

23

18

3.0

9

41

130

101

Lonmin

UG2 blend

3.6

2.7

0.06

2.8

1.2

15

21

2.1

4.1

47

340

100

Northam

2.6

3.0

0.05

0.87

1.3

17

18

2.5

5.4

47

132

97

 

 

Smelting

Smelting is intended to separate the gangue (oxide and silicate) minerals from the sulphide minerals associated with the noble metals.  The sulphide minerals form a matte that is treated further; the gangue is discarded as slag.  As the concentrate melts, two liquid phases form: a lighter silicate- and iron-rich slag with a relative density around 2.7 to 3.3, and a denser molten matte (rich in nickel and copper sulphides, and other base and precious metals) with a relative density of about 4.8 to 5.3.  Prills of molten matte grow in size by coalescing with other prills, then settle out from the slag under the influence of gravity, at a rate which depends on the viscosity of the slag.  A flux, often limestone, may be added to reduce the viscosity and liquidus temperature of the slag.

 

PGM smelting in South Africa takes place exclusively in electric furnaces at present.  Rectangular six-in-line submerged-arc electric furnaces are the most widely used, although there are also some circular three-electrode furnaces in operation.  Smelting typically takes place at temperatures around 1350ºC, although smelting of UG2 concentrates can require temperatures in the region of 1600ºC or higher.

 

Because of the low concentration of valuable minerals in the concentrate, the furnace is operated at a high slag:matte ratio (between about 4 and 9).  These two phases are tapped separately from the furnace (from opposite ends, in the case of a rectangular furnace).  The slag is tapped at temperatures around 1350ºC, and the matte is somewhat cooler, around 1200ºC.  The unwanted slag constituents are discarded (usually after being subjected to granulation using a high-flow water stream, milling, and flotation to re-capture any entrained droplets of matte).  The furnace matte contains nickel, copper, cobalt, iron, sulphur, and the PGMs.  The furnace matte is tapped into ladles and transferred by crane to a converter vessel.

 

The furnaces are normally operated with a ‘black top’, i.e. with a layer of unsmelted concentrate on top of the molten bath.  This limits the amount of radiation from the surface of the bath to the walls and roof of the furnace.  In one documented case,9 a 15 cm layer of concentrate covers a 100 cm layer of slag, which in turn covers a 58 cm layer of matte.

 

The electrical power consumption in the furnace is approximately 600 to 1100 kWh per ton of concentrate, but depends on the nature and grade of the material being treated, as well as the operating conditions in the furnace.  Electrical power accounts for approximately 40 per cent of the direct smelting costs.9

 

During smelting, some magnetite (and other spinels such as chromite) that is not reduced and fluxed, dissolves in the matte and slag.  Magnetite sometimes forms an intermediate viscous zone between the matte and slag layers, causing an increase in entrainment.  A buildup of magnetite or other spinels causes a reduction in operational furnace volume.  Near the slag-matte interface, the concentration of matte particles in slag is at its highest, as is the concentration of chromium oxide in the slag.

 

Table 6 shows the analyses of furnace matte produced in various smelters.  Note that the balance of analyses not totalling 100% is assumed to be entrained slag.  The production rate for the largest producer (Amplats Waterval smelter) is approximately 20 t/h of matte.

 

 

Table 6:  Furnace matte analyses

 

Co

%

Cr

%

Cu

%

Fe

%

Ni

%

S

%

PGM g/t

Total %

Amplats

Waterval

0.5

0.5

9

41

17

27

640

95

Amplats

Union

0.3

1.9

7

37

12

25

830

83

Impala

0.4

 

16

34

20

28

1050

99

Lonmin

Merensky

0.5

0.23

9.7

37

17

28

1000

92

Lonmin

UG2

0.5

0.29

9.8

35

17

28

2500

91

Northam

0.4

 

7.9

41

16

27

724

93

 

 

Table 7 shows the analyses of furnace slag produced in various smelters.  As a good general first approximation, the tonnage of furnace slag produced is approximately equal to the tonnage of concentrate processed.

 

 

Table 7:  Furnace slag analyses

 

Al2O3 %

CaO %

Co

%

Cr2O3%

Cu

%

FeO %

MgO %

Ni

%

S

%

SiO2 %

Total %

Amplats

Waterval

3.3

6.4

0.05

0.8

0.11

31

15

0.19

0.50

46

103

Amplats

Union

3.0

5.8

 

2.8

0.10

20

13

0.16

0.33

41

86

Impala

6

8

0.03

1.2

0.11

21

18

0.11

0.25

47

101

Lonmin

Merensky

2.0

9.8

0.05

1.2

0.09

28

19

0.15

 

44

104

Lonmin

UG2

3.9

13

0.02

2.4

0.13

9.2

22

0.11

 

47

98

Northam

1.5

10

0.03

0.8

0.10

21

20

0.2

 

44

98

 

 

Converting

During the converting process, air is blown into the molten matte, over a period of a few hours, in order to remove much of the iron and sulphur by oxidation (primarily of FeS).  The converters in operation at present are of the Peirce-Smith type; these are of horizontal cylindrical shape with an opening at the top for charging and discharging; tuyeres for blowing are arranged in horizontal rows along the lower back of the vessel; a tilting mechanism allows pouring to take place.  Silica sand is added to the converter to flux the iron oxide that is formed by the oxidation of the iron, and to form an iron silicate slag having the approximate composition of fayalite (2FeO.SiO2), with some dissolved magnetite.  Some of the sulphur leaves the system in the gas phase as sulphur dioxide (SO2).  The oxidation reaction is sufficiently exothermic to maintain a temperature around 1250ºC in the converter.  The temperature is controlled by adding cold feed or revert materials (spillages, etc.) to the converter if it becomes too hot.  The converter slag is periodically skimmed off, but the matte is poured out only once it has attained the desired iron content.  The required degree of iron and sulphur removal during converting is dictated by the choice of the subsequent refining process.  The converter matte is either cast into cast-iron moulds or refractory-lined pits, and crushed, or it can be granulated by pouring it into a very fast-flowing stream of water.

 

The converter slag requires further treatment, as the vigorously turbulent conditions cause the entrainment of prills of valuable converter matte, and the oxidizing conditions cause some of the valuable base metals (especially cobalt and nickel) to dissolve in the slag in oxide form.  In many instances, the molten converter slag is returned intermittently to the primary smelting furnace (by ladle to a cast-steel launder projecting slightly into the furnace through the matte-tapping end wall).  In other cases the slag is granulated, and subjected to milling and flotation; it is also possible to introduce the slag into a slag-cleaning furnace.  Breaking the recycle loop, by not returning the converter slag to the furnace, is rather attractive, as the quantity of PGMs locked up in this loop can represent a large financial investment.  It is not uncommon for up to a third of the matte produced in the converters to be returned to the furnace.

 

Some magnetite and chromite spinels form in the oxidizing conditions of the converting process.  If the converter slag is returned to the furnace, these can settle out and precipitate on the furnace hearth, thus considerably reducing the volume of the furnace over time.

 

Both Amplats and Lonmin smelt UG2 and Merensky concentrates largely separately, but the matte from both types of furnace is converted together.

 

The converter matte (also known as white metal) has a relative density of about 6, and consists primarily of Ni3S2, Cu2S, and FeS, along with small amounts of cobalt and precious metals.  The matte also contains small amounts of impurities such as selenium, tellurium, arsenic, lead, tin, antimony, and bismuth.

 

Analyses of converter matte and slag are shown in Tables 8 and 9.

 

 

Table 8:  Converter matte analyses

 

Co

%

Cu

%

Fe

%

Ni

%

S

%

PGM g/t

Total %

Amplats

Waterval

0.5

26

2.9

47

21

2100

97

Impala

0.4

31

0.5

47

21

3430

100

Lonmin

0.6

29

1.4

48

20

6000

99

Northam

0.5

27

1.0

51

19

2570

98

 

 

Table 9:  Converter slag analyses

 

Al2O3 %

CaO %

Co

%

Cr2O3%

Cu

%

FeO %

MgO %

Ni

%

S

%

SiO2 %

Total %

Amplats

Waterval

0.7

0.4

0.45

0.4

1.17

63

1.1

2.25

2.4

27

99

Impala

1.8

0.3

0.43

1.4

1.06

64

0.71

1.90

1.0

27

100

Lonmin

0.7

0.5

0.39

1.4

0.94

65

0.78

1.43

1.7

28

100

Northam

1.3

0.7

0.4

0.36

1.37

64

0.82

2.18

 

27

98

 

 

Off-gas handling

It remains common practice for furnace exhaust gases to pass through an electrostatic precipitator and then to be discharged to the atmosphere through a tall stack.  The SO2 in the gas can be used in the production of sulphuric acid, but the low concentration produced from the furnaces, and the intermittent production from the converters makes this challenging.

 

Of the sulphur entering the smelter, 60 per cent leaves in the converter gases, 20 per cent in the furnace gases, 15 per cent in the converter matte, and 5 per cent in the furnace slag.27  The furnace gases have an SO2 content of around 0.4 per cent, which is generally considered too low for efficient recovery.  The converter gases, for 70 per cent of the blowing time, have an SO2 content of more than 4 per cent; the overall variation is typically from 2.5 to 6 per cent.

 

Refining

The converter matte is usually milled prior to treatment in the base-metal refinery, where the copper and nickel are extracted by a sulphuric-acid leaching route.  In most plants, the leach residue makes up the high-grade PGM concentrate that is provided to the precious metals refinery for final separation of the pure precious metals.

 

 

Historical smelting developments

 

The early days

Platinum mining on a large scale began around 1926, and before the 1920s were over, no less than seven mining operations had started in South Africa.  The platinum ores were mostly processed by traditional milling and gravity-table concentration.  Flotation was used for the first time to produce a sulphide platinum concentrate in 1926, at Potgietersrus.28

 

The weakening of the platinum price in the early 1930s led to widespread closures and amalgamations, resulting in the formation of a single dominant company, Rustenburg Platinum Mines, in 1931.  By 1936, throughput had expanded to 18 000 tons of ore per month, and the oxidized ore was nearly exhausted.  It became necessary to commission a flotation plant and to install a small blast furnace and converter unit for the production of platinum-rich copper-nickel matte, which would cost less than bulk concentrate to transport to the UK refinery.  A second blast furnace was commissioned in 1953.  Blast-furnace smelting was labour intensive, and utilised expensive coke.  Furthermore, a very large volume of gas was emitted containing between 1 and 2 per cent sulphur dioxide, posing a serious pollution problem.

 

Interestingly, reverberatory smelting (where the energy is supplied by the flame generated by the combustion of coal, oil, or natural gas, as well as indirect radiation) was never applied to platinum production in South Africa, despite this technology being used quite extensively for copper production.  The probable reason for this is the difficulty in achieving the somewhat higher temperatures required for platinum smelting.  The slags produced in platinum smelting have liquidus temperatures one or two hundred degrees Celsius higher than those produced in copper smelting.

 

Electric smelting

Electric smelting was used for the first time in the primary production of platinum, with the commissioning of a 19.5 MVA Elkem rectangular electric furnace (with six in-line submerged electrodes operating in pairs in a three-phase electrical system) at the Rustenburg Section of Rustenburg Platinum Mines in 1969.  The furnace was  27.2 m long, 8.0 m wide, and 6.0 m high.  The sidewalls of the furnace were externally water cooled.  The furnace was lined with magnesite, and utilised firebrick for the roof.  Concentrates were pelletized and dried prior to being fed to the furnace.

 

Drying

There has been a significant move away from pelletization, and towards the pneumatic feeding of dried concentrates.  The lowering of the amount of moisture introduced into the furnace has lowered the energy requirement of smelting, and has drastically reduced the occurrence of ‘blowbacks’ or furnace eruptions.  This has reduced the quantity of dust emitted from the furnaces, and has significantly improved the safety and cleanliness of the smelting operation.

 

Sidewall cooling

Hatch copper-finger coolers have been installed in the sidewalls of some furnaces, and this has improved the integrity of the furnace linings.

 

UG2

Although the UG2 chromitite horizon was identified as containing PGMs in the 1920s, it took many years for this reef to be exploited.  Traditionally, the grades have been regarded as lower than those of the Merensky Reef, but more recent developments have shown that in many areas the PGM values are higher than in the Merensky Reef.

 

A blend of Merensky and UG2 concentrates has been processed since the late 1970s.  During the 1980s, Mintek developed a process for the treatment of UG2 concentrates without the requirement for blending.  Testwork25 showed that a UG2 concentrate could be produced having a PGM grade around 430 g/t, at a recovery of 87 per cent.  This was achieved with a mass pull (i.e. concentrate to ore ratio) of about 1 per cent, and a Cr2O3 content of 2.9 per cent.  Even higher grades (more than 1000 g/t) could be achieved at even higher recoveries (more than 90 per cent), if the constraint on the Cr2O3 content was relaxed (to between 4 and 10 per cent).

 

The higher concentrations of MgO, SiO2, and Al2O3 in the UG2 concentrate require a higher smelting temperature.  The Cr2O3 content of UG2 concentrate is typically seven to ten times that of Merensky concentrate, and if allowed to deposit in the furnace hearth, would rapidly build up and reduce the volume of the furnace.  Depending on the individual process, UG2 smelting may have a higher energy requirement per ton of concentrate.  For example, pilot tests22-23 demonstrated the smelting of Merensky concentrate at 1350ºC and 896 kWh/t, and UG2 concentrate at 1470ºC and 1088 kWh/t.  However, because UG2 concentrates have a higher concentration of PGMs, as a result of the small quantities of sulphide minerals in the ore, they actually require significantly less energy per mass of PGMs produced.  As shown previously, in Table 5, UG2 concentrate may have more than twice the PGM concentration than Merensky concentrate.  (In addition, the chromite content of UG2 ore is potentially saleable, after recovery of the PGMs, and the removal of gangue.)

 

Pilot-scale tests22-23 have shown that adequate coalescence of matte prills can be obtained by the use of a higher smelting temperature, and higher power flux (kW/m2 of furnace hearth area) to increase mixing in the bath.  The pilot tests led to the adoption of circular electric furnaces with three graphite electrodes for UG2 smelting, as this configuration can better withstand the higher temperature and power flux required.  The slag from this operation has a PGM content too high (2.5 to 3.5 g/t) to be discarded, so it is granulated and returned to the flotation circuit for the recovery of the PGMs.  Lime or limestone is sometimes used as a flux, to improve the compatibility of the slag with the basic refractory lining.

 

Continuous converting

Continuous converting is under investigation by a number of platinum producers.  This is seen as a way to improve environmental issues, and to de-bottleneck those plants where the converters are the limitation to increased production.  The steady stream of SO2 generated during continuous converting is suitable for sulphuric acid production.

 

South African platinum producers

 

Production data and processing details for the four South African platinum-group-metal producers are given in Table 10.

 

Table 10:  Comparison between current South African platinum producers

 

Amplats

Impala

Lonmin

Northam

Year of first production

1926

1969

1971

1992

Annual production:*

  Platinum, Moz/a

1.861

1.052

0.628

0.177

  Palladium, Moz/a

0.931

0.557

0.291

0.083

  Rhodium, Moz/a

0.177

0.112

0.088

0.015

  Gold, Moz/a

 

 

 

0.007

  Nickel, kt/a

20.6

7.7

2.88

(sold as NiSO4)

1.86

(sold as NiSO4)

  Copper, kt/a

10.9

4.5

1.74

0.98

  Cobalt, t/a

250

(sold as CoSO4)

46

0

0

Ore grades in proven reserves:

  Merensky, g/t

5.1

8.3

5.6

9.5

  UG2, g/t

4.7

9.1

6.1

6.5

Ore milled, Mt/a

22.01

14.51

9.19

1.80

% UG2 ore mined

19

46

77

~0**

Average head grade, g/t

5.52

5.17

5.16

6.25

PGM recovery in concentrator, %

Merensky: 88

UG2: 81

Platreef: 82

Merensky: 90

UG2: 79

84

90

Concentrate smelted, tons per hour (dry basis)

74

67

Mer: 4.8

UG2: 11.0

10.6

Driers

Flash driers

Spray driers

Spray driers

Flash drier

Furnaces

Waterval:

1. 39 MVA (Hatch six-in-line,

25.8m long,

8.0m wide)

2. 39 MVA

(Hatch six-in-line,

25.8m long,

8.0m wide)

 

Mortimer:

3. 19.5MVA

(Six-in-line)

1. -

Decommissioned

2. 7.5 MVA

(Six-in-line)

3. 7.5 MVA

(Six-in-line)

4. 15 MVA.

(Six-in-line)

5. 39 MVA

(Six-in-line,

25.9m long,

8.2m wide)

1. 10.5MVA (Barnes-Birlec Six-in-line, Merensky)

2. 5 MVA (Pyromet,

3-electrode,

ID 5.2m)

3. 5 MVA (Pyromet,

3-electrode)

4. 5 MVA (Pyromet,

3-electrode)

5. 2.3 MVA (Infurnco, 3-electrode)

6. 2.3 MVA (Infurnco, 3-electrode)

 

1. 16.5 MVA

(Davy,

Six-in-line,

25.9m long,

8.7m wide,

5.6m high)

 

Amplats

Impala

Lonmin

Northam

Power flux, kW/m2

165

180

Mer: 120

UG2: 235

90

Slag to matte production ratio

4.5

5.9

Mer: 3.5

UG2: 6.3

8.5

Energy requirement, kWh/t of concentrate

785

720

Mer: 1270

UG2: 880

1044

Converters

Six

Diameter 3.0m

Length 7.6m

Four

Diameter 3.0m

Length 4.5m

Two

Diameter 3.0m

Length 4.6m

Two

Diameter 3.0m

Length 6.1m

Granulation

Furnace slag

Furnace slag

Converter slag

Converter matte

Furnace slag

Converter matte

Furnace slag

Converter matte

Stack height, m

183

92

120

200

Sulphuric acid plant

Yes

Yes

No

No

Smelting

Rustenburg

& Union

Rustenburg

Marikana

Northam

Base-metal refining

Rustenburg

Springs

Marikana

Northam

Precious-metal refining

Rustenburg

Springs

Brakpan

Heraeus (Germany)

Note:  Amplats quote PGMs as 4E (Pt, Pd, Rh, Au);  Impala and Lonmin use 5PGE+Au (excluding Os); PGE refers to platinum group elements

 

*    The annual production figures reported for Impala Platinum exclude toll treatment

**  Northam has announced plans to increase UG2 production in 1999

 

 

Amplats

Amplats has two smelter plants.  The largest is the Waterval Smelter at the Rustenburg Section, having furnaces and converters.  The other is the Mortimer Smelter at the Union Section, which has one furnace (used primarily for smelting UG2 concentrates) but no converters.  The Union furnace matte is converted at the Waterval Smelter.  The Waterval Smelter is described in more detail below.

 

The first electric furnace installation for platinum matte smelting was commissioned in 1969, and has been described by Mostert27 and others.29  The 19.5 MVA six-in-line submerged arc furnace used electrodes 1.25 m in diameter, spaced 3.4 m apart.  The maximum electrode current was 32.4 kA at 201 V.  Based on the cross-sectional area of the electrodes, this results in 2.65 A/cm2.  The electrodes were normally submerged about 48 cm into the slag layer, which varied in thickness between 1.3 and 1.5 m.  The thickness of the matte layer was around 76 cm.  A second furnace was installed in the early 1970s.  The mean residence time in the furnace was around 20 hours.  A 25 per cent addition of limestone was added to the concentrate as a flux.  The resulting slag had a liquidus temperature of 1300ºC, an electrical resistivity of 4.7 Wcm at 1400ºC, and a viscosity of 3.7 poise at 1400ºC29.  A temperature gradient of 0.75ºC per cm was measured in the slag29.

 

During the 1990s, most of the smelter was upgraded.  The rotary multi-hearth driers and pelletizing plants which produced semi-dry pellets (about 10 per cent moisture) were replaced by flash driers in 1992, thereby eliminating the labour-intensive process of pellet production, as well as lowering the cost of smelting.  Flash drying technology has lower capital, maintenance, and labour costs, higher efficiency, and more effective dewatering capacity than conventional spray/rotary drying or pressure filtration technologies.  The two 18 MW Elkem furnaces were replaced by the current Hatch furnaces.  The converters were lengthened from their original 6.1 m (20 ft) to the current 7.6 m length, and their number was increased from four to six.

 

Concentrate is received from five concentrators, namely Waterval, Frank, Klipfontein, Amandelbult, and Potgietersrus.  There are three flash driers; one smaller and two identical larger units.  The dried concentrate is blended with lime, and is pneumatically transferred to the furnaces.  The two furnaces are of a Hatch design, accommodating six Söderberg electrodes 1.25 m in diameter.  Both of the furnaces at the Waterval Smelter are rated at 39 MVA (34 MW).  The two furnaces measure 25.8 m x 8.0 m inside, and have a combination of chrome-magnesite and magnesite refractories.  Based on these figures, they have a power flux of 165 kW/m2.  The maximum voltage supplied by the transformer is 350 V, and the maximum current is 27 kA per phase.  The electrode consumption is around 3.5 kg of electrode paste per MWh.  Limestone is added to the furnace as a flux, to the extent of about 10 per cent of the mass of the concentrate.  The furnace off-gases pass through recently installed ceramic filters, resulting in significantly reduced dust losses, and are then expelled to the atmosphere via the main stack.30

 

The gas produced in the Peirce-Smith converters during blowing is rich in SO2 (4 – 6%) and is routed to the single-contact-absorption sulphuric acid plant.

 

Amplats have announced5 that they are currently busy with the development of a new continuous converting process.

 

Amplats uses a matte slow-cooling process31 for the recovery of PGMs.  In this process, the converter matte (consisting predominantly of nickel, copper, and sulphur, together with minor amounts of iron, and trace quantities of PGMs) is chill-cast into 30-ton ingots in refractory-lined moulds in the ground, covered with a lid for about a day, and cooled for approximately five days.  During slow cooling, an iron-nickel phase and a copper-nickel alloy phase separate.  Around 95% or more of the platinum group elements concentrate in a relatively small volume of magnetic Ni-Cu-Fe alloy.  This alloy can be magnetically separated after crushing and milling, with the intention of shortening the overall processing time for the recovery of the noble metals.  (A quicker process reduces the hold-up of precious metals in the extraction and refining circuits.)  This enables the PGMs to be processed directly in a precious metals refinery, without the need to first pass through a base metals refinery.  In this way, a clear separation is made between the business of processing the base metals and the precious metals business.

 

 

Impala Platinum

Impala has four rectangular six-in-line submerged-arc furnaces, of which only the two largest are in use.  The furnaces are served by three Niro spray driers.  Four Peirce-Smith converters are available, of which only two operate at any given time.

 

A chronology of the furnace and drier installations is provided below:32

1969:   The 5 MW turbo-tray drier and the first 7.5 MVA furnace were commissioned

1972:   The first 7 MW spray drier and the second 7.5 MVA furnace were commissioned

1973:   The second 7 MW spray drier and the third 7.5 MVA furnace were commissioned

1974:   The first 14 MW spray drier and the 15 MVA furnace were commissioned

1986:   ‘Dry feeding’ of the furnaces was instituted

1988:   The second 14 MW spray drier was commissioned and the 5 MW turbo-tray drier was de-commissioned

1991:   The 28 MW spray drier and 39 MVA furnace were commissioned

1996:   Both 7 MW spray driers and the Number 1 7.5 MVA furnace were de-commissioned

 

The fine particle size of the concentrate presented serious problems in the drying process.  Filters became blocked; the concentrate became too dry; and dust losses increased.  Furnace blow-backs (sometimes explosive in nature) resulted from steam generation inside the furnace, and had a detrimental effect on atmospheric pollution (as well as on the loss of feed material).  Niro spray drying, to a moisture content of less than 0.5%, reduced the above problems.  Once some materials of construction problems were solved, typical running times on the driers exceeded 95%.  Dry feeding of concentrate virtually eliminated ‘blow-backs’, and made it possible to reduce the number of feed pipes from 28 to between 4 and 6, as the distribution of feed in the furnace was improved.  Dry feeding also increased furnace efficiency by 12 to 15%.  Using burnt lime in place of limestone increased smelting capacity by about 5%.

 

Details regarding all of the furnaces have been provided elsewhere32, but only those pertaining to the largest will be provided here.  The 39 MVA furnace is 25.9 m long and 8.2 m wide, and has electrodes of 1.14 m in diameter, spaced 3.32 m apart (centre to centre).  The phase current is 21 kA, and the phase voltage is 500 V.

 

Because of the high value of the PGMs, the grade-recovery relationship is heavily skewed towards maximum recovery.  This has a major impact on smelter capacity, as has Cr2O3 control in the concentrator.  The low grade of concentrate smelted, in order to maximize PGM recovery over the concentrator, has a high SiO2 and MgO content, and a low FeO content.  This requires a high operating temperature, namely 1460ºC for slag, and 1260ºC for matte.  High power fluxes help to prevent spinel build-ups, and the Cr2O3 contents of the concentrates are carefully controlled.  The Merensky concentrate has a Cr2O3 content of less than 0.5 per cent, and the UG2 concentrate runs at about 1.6 to 1.7 per cent Cr2O3.  This results in an overall Cr2O3 content of less than 1 per cent in the blended concentrate.33  Impala was the first producer to experiment with UG2 on a plant scale as early as 1971.32

 

High-quality magnesite refractory bricks are used to line the hearth and lower side walls, while firebricks are used for the upper walls and roof.  Copper cooling of side- and end-walls was provided by Hatch Associates.

 

A very low tonnage of converter matte (also known as white metal) is the final product from the smelter.  This is granulated and supplied as the feedstock for the Impala Refineries.  Impala’s Base Metals Refinery uses Sherritt Gordon ammonia leach technology.

 

All waste gases, from driers, furnaces, and converters, are treated in a Lurgi radial gas scrubber (installed in February 1999) prior to disposal.  The single-contact Lurgi-designed sulphuric acid plant is one of the few in the world running on converter gas alone.  Control is such that some furnace gas (at about 1% SO2) can also be treated.

 

Almost the entire plant throughput of concentrate is processed through the 39 MVA furnace.  The 15 MVA furnace is used primarily for the toll-treatment of a variety of materials.

 

 

Lonmin Platinum

Operations at the Western Platinum Smelter commenced in December 1971 with the commissioning of a 7.5 MVA Merensky six-in-line furnace.  In November 1982, the smelter was expanded with the commissioning of two 2.3 MVA Infurnco circular furnaces to smelt UG2 concentrate.  The UG2 smelting facilities were expanded in March 1991 with the commissioning of three 5 MVA Pyromet circular furnaces34.  Western Platinum was the first mine to commission separate facilities for treating UG2 ore for the recovery of PGMs and associated base metals35.  The Merensky six-in-line furnace has subsequently been upgraded to 10 MVA36.

 

The Merensky concentrate (received as a slurry) is filtered in a rotary drum filter and partially dried through a rotary kiln (to a moisture content of about 8 per cent) before being fed into the six-in-line furnace.  The green charge and limestone flux are manually rabbled inside the furnace.  The furnace matte is tapped periodically, while slag is tapped almost continually and granulated in a high-flow water stream.  Converter slag is returned to the Merensky furnace to recover entrained matte.

 

The UG2 concentrates, containing relatively high concentrations of chromite, are dried in spray driers.  The bone-dry concentrate is then pneumatically conveyed to one of several circular three-electrode submerged-arc AC electric furnaces.  Burnt lime is used as a flux.

 

Separate smelting plants were erected for treating UG2 concentrate, but UG2 furnace matte is combined with Merensky furnace matte for converter operation.

 

Western Platinum was the first company to exploit the UG2 on a large scale for its PGM content17.  Metallurgical investigations were undertaken in conjunction with Mintek during 1980.  Mining of the UG2 at Western Platinum Mine commenced in 1982, and the UG2 concentrator started up in March 1983.  The UG2 ore is generally milled separately from the Merensky ore.  More than 75 per cent of Lonmin Platinum’s current annual production is sourced from the UG2.  Depth of UG2 mining at Lonmin ranges from 30 m to 700 m below the surface.

 

UG2 concentrate is smelted in a circular three-electrode furnace24 with a higher power flux than is used in the Merensky furnace.  A higher than usual smelting temperature is used, and the smelting zone is more concentrated, so that the slag is more agitated.  The agitation of the slag is necessary to promote coalescence of the small quantity of matte that has to be separated from the slag.  The agitation also causes the accretion of chromite on the hearth to be minimized.  Around 80 to 90 per cent of the chromite present is discarded in the furnace slag.  Furnace matte with a chromium content of 2 per cent could be blown to converter matte containing less than 40 ppm of chromium, which is acceptable to the base-metal refinery.

 

All the converter matte is processed at the base-metal refinery (BMR), using Sherritt technology from Canada, to produce nickel sulphate crystals, pure copper cathodes, and a high-grade PGM concentrate.  The capacity of the BMR was expanded in 1991 to be able to treat 54 tons of converter matte per day.

 

Water granulation of the converter matte was introduced to prevent the formation of magnetite and trevorite (which previously formed by oxidation during cooling in moulds before crushing).  These materials did not leach significantly in the BMR and reported to the PGM concentrate.  The PGM concentrate currently has a grade of about 60 per cent35.

 

 

Northam

Northam operates the world’s deepest platinum mine, at a depth of 1750 m.  The ore grade is 10 g/t in situ, and 5.5 g/t mined.  The first smelting was carried out in August 1992, with first production in 1993.

 

Northam uses a very conventional smelting process.  Merensky concentrate (together with up to 10 per cent UG2 concentrate) is dried in a flash drier, and the dry feed is pneumatically fed to the furnace.  Burnt limestone is used as a flux.  The six-in-line furnace, supplied by Davy, is rated at 16.5 MVA (15 MW), with a normal operating range between 11 and 12 MW.  The smelter produces about 360 tons per month of converter matte37.

 

In the first leaching stage, nickel is removed as a sulphate.  The PGM concentrate is removed as the residue from a pressure leaching stage.  Finally, copper is removed by electrowinning.  The PGM concentrate is refined by Heraeus in Germany.

 

 

Limitations of the conventional process

 

1.      Environmental concerns have focused on the problem of SO2 emissions, especially the stray emissions around the mouth of the converter.  Even with a large fume hood above the mouth of the converter, fugitive emissions remain a problem.  A sulphuric acid plant is probably the most effective means of capturing the sulphur.  However, the intermittent nature of converting operations makes this rather challenging.

 

2.      As increasing amounts of UG2 concentrate are processed (to utilize deposits accessible from existing mines, and to maximize production of palladium and rhodium, as well as platinum), so the quantity of base metal sulphides decreases.  The conventional process requires sufficient matte (at least 10% of the mass of the slag) to be present to allow for effective coalescence of droplets and collection of the valuable metals.  This causes limits to be placed on the mining of ore such that only material containing more than a specified amount of nickel and copper is acceptable to the process.  This limitation can be lifted only if additional collector material is available.

 

3.      The UG2 concentrates contain significant quantities of chromite, which easily results in the buildup of (highly refractory) chromite spinel layers in the furnace.  This affects furnace operation, and the accumulation reduces the working volume of the furnace over a period of time.  This can be mitigated to some extent by the addition of some carbon to the furnace, as more reducing conditions allow for greater solubility of chromium oxide in the slag.

 

4.      The intermittent batch mode of converting is not conducive to good plant operation, and there is a significant move towards the development of continuous converting processes.

 

5.      Although most current smelters and refineries have PGM recoveries in the region of 95 to 99% each, the recovery from concentrators is only around 85%, and that from mining itself is also relatively low.  Clearly, any new processes being developed should be sufficiently flexible to allow greater recoveries in these areas, preferably by removing some of the constraints imposed by present practices.

 

6.      The long processing times in the refining of PGMs result in a large lockup of precious metals.  Sometimes, the value of the PGMs permanently locked up inside process units exceeds the capital cost of the units themselves.  The composition of the metal produced in the smelter can make a difference in reducing the length of the processing pipeline in the refinery.  This should be taken into account when investigating new processes.

 

 

Conclusions

South Africa dominates world production of platinum.  Because of the high value of the PGM products, a very risk-averse, conservative approach has been adopted to the introduction of changes in processing technology, and PGM matte smelting remains very closely based on traditional nickel-copper matte smelting.  However, platinum smelting has undergone many changes during the past three-quarters of a century, and will continue to develop further, in particular to address environmental concerns, and to maximize recovery from all available ore-bodies.  Clearly, large-scale pilot testing will be required for new processes that are currently under development, with a view to addressing the limitations of the conventional processing route.

 

 

Acknowledgements

This paper is published by permission of Mintek, and of the management of the individual platinum smelters.  Thanks are due to many friends and colleagues at Mintek and in the platinum industry for their helpful advice during the preparation of this paper.

 

 

References

1.    McDonald D. and Hunt L.B. (1982). A history of platinum and its allied metals. Johnson Matthey, London.

 

2.    Edwards A.M. and Silk M.H. (1987). Platinum in South Africa. Special Publication No. 12, Mintek, Randburg.

 

3.    Brugman C.F. (1971). A review of the platinum mining industry. Report 1206, Mintek, Randburg.

 

4.    Amplats (Anglo American Platinum Corporation Limited), Annual Report 1998.

 

5.    Amplats (Anglo American Platinum Corporation Limited), Financial Statements for the six months ended 31 December 1998.

 

6.    Implats Annual Report, 1998.

 

7.    Lonrho Platinum, 1998 Annual Report.

 

8.    Gold Fields of South Africa Limited, Annual Report 1998.

 

9.    Newman S.C. (1973). Platinum. Transactions of the Institute of Mining and Metallurgy 82, A52-A68.

 

10.  Platt’s Metals Week. vol.70, no.9, 1 March 1999.

 

11.  Cowley A. (1998). Platinum 1998. Johnson Matthey, London.

 

12.    Hilliard H.E. (1999). Platinum-Group Metals. US Geological Survey, Mineral Commodity Summaries, January 1999,

http://minerals.usgs.gov/minerals/pubs/commodity/platinum/550399.pdf

 

13.  Roskill (1985). The economics of platinum group metals 1985. Third edition, Roskill Information Services, London, p.165.

 

14.  Roskill (1994). Platinum: Market update, analysis & outlook. Roskill Information Services, London, p.67.

 

15.  Von Gruenenwaldt G. (1977). The mineral resources of the Bushveld Complex. Mineral Science and Engineering, vol.9, no.2, April 1977, pp.83-96.

 

16.  Vermaak C.F. (1995). The platinum-group metals: A global perspective. Mintek, Randburg, (especially pp.11,13,22).

 

17.  van der Merwe J.J., Vermaak A.H., Slabbert M.J., Mauve A.C., and Mooney D.J. (1998). An overview of the geology of the UG2 Chromitite Layer and its surrounding lithologies on Lonrho Platinum’s lease area. 8th International Platinum Symposium, 28 June – 3 July 1998, Rustenburg, Geological Society of South Africa and The South African Institute of Mining and Metallurgy, pp.403-406.

 

18.  Roskill (1994). Platinum: Market update, analysis & outlook. Roskill Information Services, London, p.23.

 

19.  Edwards A.M. and Silk M.H. (1987). Platinum in South Africa. Special Publication No. 12, Mintek, Randburg, p.52.

 

20.  Barnes A.R. and Finn C.W.P. (1981). The behaviour of UG-2 chromite during smelting. Report 2112, Mintek, Randburg.

 

21.  Vermaak C.F. (1995). The platinum-group metals: A global perspective. Mintek, Randburg, pp.86-87.

 

22.  Mintek (1987). The successful development of an industrial process for the recovery of platinum-group metals from the UG-2 Reef. Application Report No.1, Mintek, Randburg.

 

23.  Liddell K.S., McRae L.B., and Dunne R.C. (1985). Process routes for beneficiation of noble metals from Merensky and UG-2 ores. Extraction Metallurgy ’85, The Institution of Mining and Metallurgy, London, 9-12 September 1985, pp.789-816.

 

24.  Corrans I.J., Brugman C.F., Overbeek P.W., and McRae L.B. (1982). The recovery of platinum-group metals from ore of the UG-2 Reef in the Bushveld Complex. Twelfth Congress of the Council of Mining and Metallurgical Institutions, Johannesburg, The South African Institute of Mining and Metallurgy, 3-7 May 1982, Volume 2, pp.629-634.

 

25.  Overbeek P.W., Loo J.P., and Dunne R.C. (1984). The development of a concentration procedure for platinum group metals and chromite from the UG-2 reef of the Bushveld Complex. First International Symposium on Precious Metals Recovery, Reno, Nevada, 10-14 June 1984, Paper XVIII, 27pp.

 

26.  Roskill (1994). Platinum: Market update, analysis & outlook. Roskill Information Services, London, p.5.

 

27.  Mostert J.C. and Roberts P.N. (1973). Electric smelting of nickel-copper concentrates containing platinum group metals at Rustenburg Platinum Mines Limited. Journal of South African Institute of Mining and Metallurgy, vol.73, no.9, pp.290-299.

 

28.  Edwards A.M. and Silk M.H. (1987). Platinum in South Africa. Special Publication No. 12, Mintek, Randburg, p.52.

 

29.  Urquhart R.C., Rennie M.S., et al (1974). The smelting of copper-nickel concentrates in an electric furnace. Report 1664, Mintek, Randburg, 27 September 1974.

 

30.  Wicks J. (1999). Amplats, Personal communication, September 1999.

 

31.  Schouwstra R.P., Rixom P.M., Roberts J.R. de R., and Bruwer J.S. (1998). The effect of cooling rates on converter matte alloy microstructure: a laboratory study. 8th International Platinum Symposium, 28 June – 3 July 1998, Rustenburg, Geological Society of South Africa and The South African Institute of Mining and Metallurgy, pp.363-366.

 

32.  Watson G.B. and Harvey B.G. (1992). A common sense approach to process improvements to electric smelting of nickel-copper concentrates at Impala Platinum. Non-ferrous Pyrometallurgy: Trace Metals, Furnace Practices and Energy Efficiency, Proceedings of the International Symposium , Bergman R. et al (eds.), The Metallurgical Society of the Canadian Institute of Mining, Metallurgy and Petroleum.

 

33.  Highcock G.A. (1999). Impala Platinum, Personal communication, May 1999.

 

34.  Hay K. (1999). Lonmin Platinum, Personal communication, March 1999.

 

35.  Steenekamp N. and Dunn G.M. (1999). Operations of and improvements to the Lonrho Platinum base metal refinery. EPD Congress, The Minerals, Metals & Materials Society, pp.365-378.

 

36.  Assad C.S. (1999). Lonmin Platinum, Personal communication, May 1999.

 

37.  Derbyshire J.R. (1999). Northam Platinum, Personal communication, May 1999.